Air conditioning Hampton East homes need follows the post-war house. Wikipedia describes Hampton East as a residential suburb mainly developed during the 1950s, and the ABS 2021 Census counts 56.9% of its occupied dwellings as separate houses, 22.1% as semi-detached, row or townhouses (Victoria 13.9%) and 20.7% as flats. Peak Air Conditioning Brighton quotes split system and multi-head installs, ducted air conditioning and reverse cycle heat pumps, cleans wall splits, services gas ducted heaters and rooftop evaporative coolers, and finds faults across this City of Bayside suburb, from the South Road commercial precinct to the streets around GL Basterfield Park. This page sets out each job by house frontage, the fibro, brick veneer and open front gardens that shape an install, and indicative Melbourne prices. Calls are taken from 6am to 10pm every day.
GET A FREE QUOTE
Two things shape how a heating or cooling job in Brighton starts: knowing what each option costs before anything is booked, and finding a visit time that suits the household. Peak Air Conditioning Brighton is set up around both. Prices are put in writing after the site visit, option by option, and the phone line takes bookings for new systems, servicing, aircon cleaning and repairs from 6am to 10pm, seven days a week.

The frontage of a Hampton East house is a good first guide to its cooling layout. Bayside City Council's 2024 Hampton East Urban Forest Precinct Plan describes intact single and double storey post-war houses that are often double or triple fronted, standing among new detached houses and dual occupancies, and the ABS 2021 Census counts 22.1% of the suburb's occupied dwellings as semi-detached, row or townhouses, against 13.9% for Victoria, with 30.9% of homes having two bedrooms against 19.1% for the state. The three parts below take each house form in turn. This section deals with the system and where its parts go for cooling; kilowatt sizing and heating sit in the heating section, and what the walls and eaves mean on install day sits in the install checks section.
A double-fronted house shows two front rooms to the street. Where those rooms sit either side of a central hall, which the visit confirms room by room, the layout suits a split system in each front room, each one on a side wall of its own room. The precinct plan says Hampton East houses are usually set back from both side boundaries, so each side of the house has a strip of ground beside it, and that strip is where an outdoor unit and its pipe run can go without crossing the hall or the roof. Split system installation for a house like this is usually two short runs, one down each side, rather than one long run to a single spot at the back.
Run length is the limit to plan around. Mitsubishi Electric's installation manual for its MSZ-AP wall splits allows up to 20 m of pipe between the indoor and outdoor unit on its smaller models, with the first 10 m needing no extra refrigerant and 20 g added for each metre beyond it, and a height difference of up to 12 m. A bedroom behind a front room on the same side can follow the same side run, so a second unit there stays well inside those limits. Where an owner wants three or four rooms done, Climate Control Solutions, a Melbourne installer, says that past two rooms a multi-head system usually costs less than the same number of separate splits because only one outdoor unit is bought and installed, while separate splits still win when the rooms are far apart, when the spend is staged one room at a time, or when one outdoor unit has nowhere sensible to go. On a house with rooms down both sides of a hall, that choice is set out on the quote. Split system installation describes the install itself step by step.
A triple-fronted house steps its front wall back in three planes, so its rooms are spread across a wide face of the house rather than lined up along one hall. Reaching rooms laid out like that from a single wall unit is hard, but each of them can be reached from the roof space, which is where ducted air conditioning runs. Daikin's ducted page describes ducted systems as designed for whole-home coverage while split systems suit individual rooms, with one central unit serving several zones instead of several outdoor units. Rinnai's ducted page lists sufficient roof or ceiling space for ductwork as a requirement and says retrofitting into an existing home may need extra installation work, so the roof inspection comes before any layout is drawn.
YourHome, the Australian Government's guide to sustainable housing, says ducts for ducted air conditioners must be insulated to at least R1.5 with joints sealed to prevent condensation and leakage, and that ducts should be the correct size with adjustable outlets. On a single storey post-war house, one indoor unit in the roof space and one outdoor unit at the side or rear can then reach rooms on all three faces of the frontage through ceiling outlets, so no front room carries a wall unit and the street face stays clear. Zoning is the setting to decide early: YourHome says zoned systems cool only occupied areas and allow different conditioning in living and sleeping areas, which suits a house whose living room and bedrooms sit on different faces of the frontage. The inspection checks the roof hatch, the path between the ceiling joists and the outdoor unit position. A ducted reverse cycle system also heats through the same outlets, and the heating section covers that side. Ducted air conditioning covers zone controllers and system sizes in more detail.
Most of Hampton East's newer homes are smaller ones. The precinct plan forecasts the suburb's dwellings to grow by an average of 43 a year to 3,260 in 2041, as dual occupancies, town houses and low-rise apartment buildings, and says most new residential development has been delivered inside the Hampton East Activity Centre, where the Activity Centre Zone sets height limits of three to six storeys depending on how close a site is to the centre's heart. The Bayside Planning Scheme's Clause 73.01 defines an apartment as a dwelling above the ceiling level or below the floor level of another dwelling, so most apartments have no roof space of their own for a duct to cross, and a townhouse built with a low or flat roof may have little more.
Where the roof space is missing, the answer is a wall split system in each room that needs cooling, usually the living area first and then the bedrooms. Whatsthedamage, a Melbourne cost guide, calls multi-head systems a popular choice for Melbourne townhouses and apartments where ducted is not feasible, because one outdoor unit can run several indoor units without ductwork, which helps where a courtyard or balcony has room for only one condenser. Height is the second check in a taller building. The MSZ-AP limit of 12 m between indoor and outdoor unit means that an upper apartment in a six-storey block may sit too high above a ground-level position, so its outdoor unit goes on the apartment's own balcony or an approved roof position instead. In a block with an owners corporation, the model rules published by Consumer Affairs Victoria require written approval before the external appearance of a lot is changed, so that approval is obtained before an outdoor unit position is fixed.
Bayside's precinct plan describes Hampton East's post-war houses as built in cream and red brick, weatherboard or fibro, behind gardens that are mostly low lying and front fences that, where they exist, are mostly low or open. Each of those three things changes something on install day: where a pipe hole can be drilled, how the wall is sealed afterwards, and where the outdoor unit and pipe covers can sit without facing the street. The three parts below take each in turn and end with the check that settles it. The choice of system belongs to the installation section; this section is about the wall, the eaves and the street face.
Fibro is a real install question in a suburb Wikipedia describes as mainly developed during the 1950s. The Better Health Channel, run by the Victorian Department of Health, says asbestos was commonly used in building materials between the 1940s and the late 1980s, and that houses built before the mid-1980s are highly likely to have asbestos-containing products. Its list for older homes includes exterior fibre cement cladding, known as AC or fibro, and flexible building boards such as eave linings. It says asbestos fibres may be released when the material is drilled, sanded or cut with a power tool, that it is difficult to tell by looking whether a sheet contains asbestos, and that the only way to be certain is to have a sample tested by an accredited laboratory. Until it is tested, the page says, the material should be treated as though it contains asbestos.
That sets the order of work on a fibro house. Before any pipe hole or bracket fixing goes through a wall or an eave, the installer looks at what the sheet is. Where it is suspect, there are two honest options: have a sample tested first, or move the pipe route to a wall that is not fibro, such as a brick section or a newer addition, and keep the outdoor unit bracket off the sheeting. The Better Health Channel says power tools should not be used to drill or break any asbestos product, so a suspect sheet is never drilled to find out. Removal is a separate trade: the page says a list of licensed asbestos removalists is available from WorkSafe Victoria, and an air conditioning installer does not remove asbestos. The quote records which route was chosen and why.
Sustainability Victoria's archived page names brick veneer walls as typical of double-fronted post-war houses, and the precinct plan describes Hampton East's as cream and red brick. As a general rule of how brick veneer is built, the wall is an outer skin of brick, an air cavity, and a timber frame lined inside, so a single pipe hole passes through three layers before it reaches the room. Mitsubishi Electric's MSZ-AP installation manual sets that hole at 65 mm, falling 5 to 7 mm towards the outside so that water runs out rather than in, and fits a wall hole sleeve, which it says keeps the connecting wire off metal parts in the wall and prevents damage by rodents where the wall is hollow. The manual then has the gap around the sleeve sealed with putty, so the cavity is closed to weather and pests.
The run is then dressed and sealed. The same manual has the pipes fixed to the outside wall with fixing bands, a wall hole cover fitted, the piping insulated to stop condensation dripping, and the pipes protected from external damage. The MSZ-AP manual also places the drain hose below the refrigerant piping and pointing downward for easy drain flow, so the bundle leaves the brick with the drain at its base. The visible brick face is worth thinking about on cream brick in particular, since a pale wall shows a pipe cover clearly, so covers are chosen to sit neatly against the brick and run down to the outdoor unit by the shortest path. Where the room's best position is on a front wall, the pipe usually goes through the side wall instead, which keeps the bundle off the street face described in the front fences part below.
With mostly low or open front fences, the front of a Hampton East house is on show. The precinct plan shows Hampton East in precincts D2 and G3 of Clause 15.01-5L, Bayside's preferred neighbourhood character policy, and the policy text for D2 asks for low, open style front fencing other than along heavily trafficked roads, while G3 asks for a low, permeable front fence or none, with a fence of up to 1.2 metres as a guideline. The plan says front setbacks run from 6 to 8 metres. That policy guides new development rather than air conditioners, but its effect is the point: a condenser on the front wall or a pipe cover up the facade would be seen from the footpath, so outdoor units and pipe covers go to the side or rear of the house. The MSZ-AP installation manual's outdoor checklist adds good airflow, a firm base and a spot where neighbours are not bothered by operating sound or by hot or cool air.
A few Hampton East properties also carry heritage controls. The Schedule to the Heritage Overlay in the Bayside Planning Scheme, read on the State planning portal on 20 November 2026, names five Hampton East places: HO501 at 11 Guernsey Avenue (Guernsey House), HO544 at 26 Nepean Avenue, HO616 at 12 Oswald Thomas Avenue (Stonehaven), HO629 at 124 Wickham Road, which has external paint controls, and HO715 at 20 Kelly Avenue, a lemon-scented gum with tree controls. None is on the Victorian Heritage Register, and Bayside's Heritage Precincts page lists no precinct in Hampton East. For those places, Clause 43.01-1 needs a permit for an air conditioner on a house if it is visible from a street, other than a lane, or a public park, and Bayside's local heritage policy, Clause 15.03-1L, says to site air conditioning plants so they are concealed from the street. Check the address on VicPlan and check with Bayside City Council before the position is fixed.


Hampton East is a mix of owners and renters. The ABS 2021 Census counts 27.8% of homes owned outright and 34.2% owned with a mortgage, and 34.6% rented, against 28.5% for Victoria, with a median weekly rent of $400. So a system is bought either by a household that lives in the house or by an investor who lets it. Peak Air Conditioning Brighton works across the City of Bayside, Hampton East included. Refrigerant work is done under an ARC licence, which can be checked on the ARC's Look for the Tick search, electrical work by a licensed electrician, checkable on Energy Safe Victoria's public registers, and gas work by a gasfitter registered with the Building and Plumbing Commission.
Hampton East households are working ones. The ABS full QuickStats count 58.3% of employed residents working full-time, against 56.2% for Victoria, and 47.3% of families are couples with children, while the precinct plan records 39.6% of residents travelling to work by car. A household like that rarely has a free weekday morning, so bookings are taken from 6am to 10pm, seven days a week: a call before leaving for work, or an inspection and quote after dinner. Same-day visits happen where possible, but none is promised.
The line's hours are not drilling hours. EPA Victoria's residential noise rules restrict power tools before 7am and after 8pm on weekdays, and before 9am and after 8pm on weekends and public holidays, so a 6am call books the job rather than starting it, and wall drilling, core holes and bracket fixing happen inside EPA's hours. What fits the evening is the quiet part of the job: looking at the switchboard, the roof hatch, the side paths and the rooms, and talking through the options. A booking made that way can settle the visit time, the parking for the installer's vehicle and access through a side gate before install day, so a full-time household loses as little of the working week as possible.
An investor usually decides from a distance, so each job is quoted in writing after an inspection, naming the model and its kW, each indoor and outdoor position, the pipe route, any switchboard work and any approval the job depends on. The certificates are listed on the quote too. Energy Safe Victoria says a Certificate of Electrical Safety is a legal document, that air conditioning is non-prescribed electrical work with a copy due to the customer within 30 days, and that where a rental provider or agent engaged the electrician, a copy can be requested from the customer or from Energy Safe. Where gas work is done, the Building and Plumbing Commission says a compliance certificate must be issued for installing, relocating or replacing any Type A gas appliance, whatever the cost, and only licensed plumbers can issue one.
Those papers go into the owner's or agent's records, alongside the two-yearly checks Consumer Affairs Victoria requires of rental providers: a gas safety check by a licensed or registered gasfitter and an electrical check by a licensed or registered electrician, every two years. CAV says the rental provider must tell a renter the date of the last gas safety check before the agreement starts, and give a copy within 7 days of a written request. Energy Safe notes that the rental safety check uses its own form, not a Certificate of Electrical Safety. For heating, CAV's minimum standards require a fixed heater in the main living area, energy efficient for agreements from 29 March 2023, and the Victorian Energy Upgrades program says a space heater that breaks and cannot be repaired after 1 March 2027 must be replaced with an efficient reverse cycle air conditioner; landlords should check the current CAV rules. Manufacturer warranty applies when a system is installed to the manufacturer's requirements.
Hampton East grew late. Bayside's precinct plan says the area was subdivided in the 1850s into 0.8 hectare parcels used mostly for market gardening, stayed rural and thinly settled until the Second World War, then filled with suburban development as commerce and industry grew along the Nepean Highway, and was largely developed by the 1970s. Wikipedia records that the post office opened on 1 September 1947, closed in 1950 and reopened in 1956, and counts 5,069 residents at the 2021 census. The three parts below follow the commercial precinct, the small shopping strip and the streets around the suburb's central park.
Bayside's 2016 structure plan for the Hampton East activity centre describes a commercial precinct spanning the south-west side of the Nepean Highway and South Road intersection, part of the wider activity centre around the station. It calls the Hampton East section a recognised office location with organisations across health, business services, finance and government, and notes a strong presence of health providers in both purpose-built office buildings and ground floor retail, alongside several specialist outdoor adventure clothing shops on the Nepean Highway retail precinct, with shop-top apartments above. The precinct plan repeats the aim of a health focus within the South Road Commercial Precinct. Schedule 1 to the Activity Centre Zone in the Bayside Planning Scheme now carries that aim as scheme text: its South Road Commercial Precinct objectives encourage apartment development that can accommodate medical office suites on the ground and first floors, and its guidelines send service vehicles to the rear laneways.
For the plant, the same schedule asks the council to consider, on any application, whether site services, roof plant and equipment are sufficiently screened or hidden from view, which points condensers to a screened roof position or the rear laneway side rather than the South Road frontage. Clause 62.02-2 exempts services normal to a building other than a dwelling, including heating and cooling systems, unless the scheme specifically requires a permit, so whether new plant on an existing building needs one is a question for Bayside City Council before the position is fixed. Inside, the layout follows the tenancy's own rooms, which the inspection maps before any unit is chosen. For ongoing care, whatsthedamage's commercial guide describes quarterly maintenance covering filters, coil cleaning, condensate treatment and electrical checks, and on ducted air-handling systems the hygiene items AS/NZS 3666 expects. Commercial air conditioning covers multi-unit sites and maintenance contracts.
Bayside's Small Activity Centres Strategy (updated March 2019) lists Keith Street and Widdop Crescent, Hampton East, as a Small Neighbourhood Activity Centre in the Mixed Use Zone, and says the small strip already has a significant proportion of inactive street frontages associated with non-retail uses. OpenStreetMap places Keith Street, Curley Rourke Reserve and Oswald Thomas Avenue in Hampton East, with the reserve close to the Keith Street end of the strip and Oswald Thomas Avenue to the north of the reserve. A small shop or office tenancy in a strip like this usually has one or two rooms to condition, so the job is a wall split or ceiling unit for each, with the outdoor unit at the rear rather than on the shopfront, and the tenant checks the lease and the building owner's consent first.
Oswald Thomas Avenue carries one of Hampton East's five heritage listings: HO616, Stonehaven, at 12 Oswald Thomas Avenue. The schedule applies solar energy system controls to it but no external paint or tree controls, and it is not on the Victorian Heritage Register. For a listed house, Clause 43.01-1 counts a public park as well as a street: an air conditioner visible from either needs a permit, so a wall facing a reserve is treated like a wall facing the street. Clause 43.01-4 exempts these domestic services applications from the notice and objector review steps, and the Clause 43.01-1 table makes installing domestic services on a dwelling a VicSmart class assessed under Clause 59.07. Bayside's Clause 15.03-1L asks for air conditioning plant to be concealed from the street, so the outdoor unit goes behind the house. For any other house nearby, the schedule names no further Oswald Thomas Avenue or Keith Street address; check VicPlan and with Bayside City Council for the address itself.
GL Basterfield Park is the green space in the middle of the residential streets. By their OpenStreetMap positions, Besant Street lies to its south, Leith Crescent to its west and Flowerdale Road to its east, all in Hampton East 3188, with Spring Road Park a short way east and Wishart Reserve further to the north-west. The precinct plan says most of Hampton East's housing land is in the Neighbourhood Residential Zone, with a two-storey height limit, where new work is usually an addition to an existing house or a new house or dual occupancy in place of the original one. So, as the plan describes for the suburb as a whole, original post-war houses can stand beside newer two-storey rebuilds here, and the Heritage Overlay schedule names no address on Besant Street, Leith Crescent or Flowerdale Road. The install questions here are about neighbours and siting rather than heritage.
With houses set back from both side boundaries, an outdoor unit placed down a side path is close to the house next door. The MSZ-AP installation manual asks for an outdoor position where neighbours are not bothered by operating sound or by hot or cool air, so the unit faces into the owner's own yard rather than at a neighbour's bedroom window. Mitsubishi Electric's MSZ-AP product page says its Night Mode reduces the outdoor unit's operating noise by up to 3dB(A), and its operating manual notes that the outdoor noise does not drop when the indoor unit runs on a multi system, so a multi-head outdoor unit is placed with that in mind. Where a rebuild has replaced the original house with two dwellings, each dwelling needs its own system and its own outdoor position. A side wall that faces the park is a choice for the owner, since no heritage control applies on these streets, but the same siting rules keep the condenser out of view from the footpath.


Heating in Hampton East starts with what sits above the ceiling. Sustainability Victoria's archived guide to renovating a double-fronted brick veneer house, one of the post-war types the precinct plan describes, says these homes are typically built with brick veneer walls, metal-framed windows, a tiled roof and timber floors, and are likely to have no insulation in the walls or floors and only a small amount in the ceiling. The Energy Rating calculator, checked on 20 November 2026, says postcode 3188 spans more than one climate zone and allocates it to the Cold zone, so the heating stars on a unit's label are the ones to compare. The two parts below take the older house and the newer townhouse in turn.
A heat pump is sized to the heat the house loses on a cold night, and a thinly insulated ceiling is one of the largest losses. YourHome's insulation guide says installing roof and ceiling insulation can save 45 percent or more on heating and cooling costs, and Sustainability Victoria's archived page says topping up existing ceiling insulation will improve winter comfort and reduce energy use and bills, while older homes develop gaps and cracks over time that lose heat in winter. So the inspection looks into the ceiling before a kilowatt figure is chosen: how much insulation is there, whether it has been disturbed, and whether downlights or a heater flue need clearance around them. Mitsubishi Electric's buying guide says sizing is not as simple as looking at a home's floor area, calls for a professional heat load calculation, and lists insulation, the sides that face the sun, the size, type and orientation of windows and doors, and taller ceilings among the factors, so the heat load result settles the size rather than the room's square metres.
The figures show why the order matters. Mitsubishi Electric's MSZ-AP range steps its rated heating output from 3.2 kW on the AP25 through 3.7, 5.4, 6.0, 6.8 and 8.0 kW to 9.0 kW on the AP80, and its cold-zone heating stars fall from 3 on the smaller models to 2 or 2.5 on the larger ones, so a room that needs one step up because of a bare ceiling costs more to buy and to run. energy.gov.au says reverse cycle air conditioners are 300% to 600% efficient because they move heat rather than make it. A household can top up the ceiling or draught-proof first and size the heat pump to the improved house, or install now; either way the installer sizes it to the house as it stands on the day, and the quote says which assumption it uses. Where a house already has a gas ducted heater, a heat pump in the main living area is one option the quote can price beside replacing the heater, so the owner can compare the two.
A townhouse built in recent years has had less time to develop the gaps and cracks that Sustainability Victoria says older homes accumulate, and the visit checks how well a particular one holds its heat rather than assuming it from the build date. Two systems fit. The first is a reverse cycle split in each main room, usually the living area and the main bedroom, each sized to its own room. The second, where the townhouse has a usable roof space, is electric ducted heating in the form of a ducted reverse cycle system: Mitsubishi Electric's ducted page describes it as a heat pump that draws heat energy from the outside air and transfers it indoors, even in cool conditions, through the same ducts that carry cooling.
Either system runs best on steady, moderate settings. energy.gov.au says each degree of extra heating in winter increases energy use by between 5% and 10%, and Mitsubishi Electric's ducted page lists a consistent target temperature, zoning and closed doors among the ways to run a system efficiently. The MSZ-AP operating manual allows up to 28 on or off timers a week, each with its own temperature, so a split can warm the living area before the household gets home and drop back overnight without being left on high. Timers also matter for the neighbours, since many townhouses share a wall: EPA Victoria's residential noise table restricts a heat pump used for heating before 7am on weekdays, before 9am on weekends and public holidays, and after 10pm, so an early morning warm-up is set to start inside those hours.
On a post-war Hampton East house the parts that need looking after sit in three places: wall splits inside, a gas ducted heater under the floor or in the roof space, and an evaporative cooler or outdoor unit on the roof or beside the house. energy.gov.au advises a regular service inspection by a licensed technician before peak use, giving late spring and autumn as examples, and wiping down filters and dust around the indoor and outdoor units between services. The three parts below plan each visit around where the part sits, and each names the trade licence that work falls under.
This part is about the unit, not health. A wall split collects dust and moisture inside, and Mitsubishi Electric's MSZ-AP operating manual says dirt or dust in the unit may create an unpleasant odour or clog the drain passage and cause water to leak from the indoor unit, and that the owner should never try to wash the inside of the indoor unit. Daikin's FTXF operation manual likewise says an odour absorbed into the unit is blown out with the air flow and recommends having the indoor unit cleaned, and that its automatic drying mode is not designed to remove existing dust or mould. Aircon cleaning is the visit that deals with those parts: QuickAir, a Melbourne installer, describes a deep clean as one where the indoor unit is stripped and the coils, fan barrel and drain pan are washed rather than wiped.
The owner's part is the filter. Daikin's manual says to clean the filters about every two weeks, since clogged filters waste energy, and Mitsubishi Electric's manual gives the same two-week interval with a vacuum or a rinse and drying in the shade. A clean is not a service, though. A service adds the electrical, drain and operating checks that a filter wash cannot, and Daikin's manual recommends periodical maintenance by a specialist in addition to the user's own cleaning, because the inside of a unit may become dirty after several seasons. Mitsubishi Electric's manual says to stop using the unit and call for service when water drips from the indoor unit, the operation lamp blinks or the breaker trips often. Refrigerant work during a service falls under an ARC refrigerant handling licence.
A gas ducted heater in a Hampton East house may sit under a raised timber floor, in the roof space or outside against a wall; no source read for this page counts which, so the visit finds it first. Wherever it sits, the service follows the manufacturer's schedule. Seeley International's Braemar ducted gas heater owner's manual sets a check every two years by a qualified, licensed technician covering the heat exchanger, the gas and electrical connections, the burners and ignition, the flue system and cowl, the return air grille and filter, the duct condition and the zone operation, with each visit signed off in the schedule. Energy Safe Victoria's gas heating guide says a qualified gasfitter will inspect the heater and its installation, including testing for carbon monoxide leakage, and lists a partly or fully blocked flue among the causes of high carbon monoxide. The Building and Plumbing Commission says only plumbers registered or licensed in the specialised class of Type A appliance servicing may carry out that work.
The ducts and registers are cleaned as a separate job. Brivis's ducted gas heater operation manual describes duct cleaning as removing dust and odours, cleaning the return air filter, the return air grille and duct, the heater fan and its assembly, and the supply air registers and their boots. Mr Duct, a Melbourne cleaner, says ducts in tight crawl spaces and ceiling cavities take longer to reach, which is the case for an underfloor heater whose outlets sit in the floors. In a roof space, YourHome's insulation guide says clearances must be left around hot objects such as heater flues, so the visit also checks that insulation has not been pushed against the flue. Between services, Braemar's manual asks the owner to clean the return air filter at least every two weeks during the heating season. Ducted heating service and repairs covers fault codes and heater replacement.
An evaporative cooler sits on the roof, so its service is a roof job. Seeley International's Breezair owner's manual sets a residential service every two years, before the summer season, covering the pads and pad frames, the tank, the pump and its filter, the drain valve, the bleed funnel, the float valve, the motor and fan, and the roof penetrations and support frame, then checks for leaks and water distribution across the pads. For coolers with a bleed system it adds seasonal visits before and after summer: water on and pads cleaned or replaced in spring, then water off, the tank drained and cleaned and the bleed funnel removed for the winter. Seeley's Coolair manual says the bleed adds fresh water continually to dilute the salts that evaporation leaves behind in the tank. The Breezair manual also warns that climbing onto the roof can be hazardous and lists a roof pitch over 30 degrees or a roof access point more than 4 m above the ground among the conditions that may add access charges. The Quote Yard says pads typically need replacing every two to five seasons, depending on the water. A pre-summer evaporative cooler service checks the water flow across the pads before the first hot day.
A cooler that breaks down or stops cooling is fault-found from Seeley's own troubleshooting tables before any part is replaced. For inadequate cooling, the Breezair manual lists dry pads first, which means checking that the water supply is on and that water reaches the pads, then too few exhaust openings in the house, then excessive humidity, on which it says the cooler will not reduce the temperature as much as on drier days. Coolair's manual adds, for some of its models, dry patches in the pads, traced to blockages in the lid's water distribution channels, and both manuals treat the smell from new pads as normal, fading after some hours of running. So the visit separates a water or airflow problem, which the service fixes, from a pump, valve, motor or electronics fault that needs a part, and the quote says which it is.
The outdoor unit of a split or ducted system sits beside the house or on a bracket, and a breakdown there starts with fault finding, not refrigerant. Mitsubishi Electric's operating manual says that when the system does not cool or heat, refrigerant leakage is one possibility, and The Quote Yard says a leak must be found before anything is recharged, using electronic detectors, ultraviolet dye or a pressure test with nitrogen. It adds that a failed capacitor is confirmed in minutes, while an intermittent electrical fault or a slow refrigerant leak can take hours to pin down, and that the outdoor fan works harder and fails more often where the unit sits in full western sun. Repairs on the refrigerant side are done under an ARC licence; wiring faults go to a licensed electrician. Evening bookings run until 10pm.


The figures below are indicative ranges from Melbourne cost guides, installers and the Victorian Energy Upgrades program, read in November 2026. They are those sources' estimates, not this business's prices, and a written quote follows a visit. For a fault, The Quote Yard's Victorian repairs page gives a general attendance and diagnosis fee of $120 to $250, usually credited against the repair if it goes ahead, and its Melbourne table gives call-out fees from $120 to $280 across its five Melbourne regions. Its suburb list, read on 20 November 2026, does not name Hampton East and has no Bayside fee row, so the call-out is confirmed at the quote.
Split system installation is priced by size and by how far the outdoor unit sits from the indoor one. Climate Control Solutions' Melbourne calculator (last reviewed July 2026) gives indicative installed prices of $1,900 to $2,500 for 2.5 kW, $2,300 to $2,900 for 3.5 kW and $2,700 to $3,500 for 5.0 kW, and says a 3.5 kW back-to-back job lands at around $2,100 to $2,600. hipages' national guide puts a simple split supplied and installed at $1,400 to $3,000. A double-fronted house wanting both front rooms done has a choice the same calculator prices directly: two separate 3.5 kW splits at about $4,600 to $5,800 installed, against about $4,000 to $5,200 for a two-head multi-head system on one outdoor unit. Whatsthedamage's Melbourne table (updated November 2026) puts a four-head system at $7,350 to $12,600, typically $8,900, for a house that wants the bedrooms done as well.
For a two-bedroom townhouse, whatsthedamage says ducted can be more system than the home needs, which points to splits or a two-head multi-head. Where the owner supplies the unit, its install-only range is $735 to $1,575. The common extras are wiring and removal: Climate Control Solutions says to allow roughly $450 extra where a new circuit is needed for the licensed electrical work, and that removing an old unit adds about $250 per unit. Where a split replaces a non-ducted gas room heater, the Victorian Energy Upgrades program lists household discounts of $630 to $1,610 for a 3 kW to 9 kW reverse cycle unit. A long side run, an upper-floor bracket or a fibro wall that moves the pipe route are what push a quote towards the top of these ranges.
The ABS counts 39.7% of Hampton East homes with three bedrooms and 22.8% with four or more, and whatsthedamage's Melbourne table splits ducted reverse cycle quotes along that line. A three-bedroom home, or a single-storey four-bedroom home with good roof access, falls in its standard band at $8,400 to $14,700, typically $11,550. A larger four-bedroom home, a two-storey house or a system zoned room by room falls in its premium band at $12,600 to $23,100, typically $16,800. QuickAir, a Melbourne installer, gives $8,000 to $14,000 as a typical outcome for a three to four bedroom home. For ducted air conditioning in a single storey triple-fronted house, the roof access and the number of zones decide which band the quote lands in.
Electric ducted heating is priced inside the same figures, because a ducted reverse cycle system heats and cools from one electric system; whatsthedamage notes that gas ducted only heats and needs a gas connection and a flue. None of the cost guides in the pricing file gives a separate price for a resistance-element electric ducted heater, so no figure is given for one here. For comparison, the same table puts gas ducted heating supplied and installed at $4,000 to $11,550. The Victorian Energy Upgrades program lists household discounts for swapping a ducted gas heater for ducted reverse cycle of up to $2,520 at 10 kW, $4,200 at 16 kW and $5,530 at 22.4 kW, and up to $5,460 for replacing central electric resistance ducted heating, for approved products with at least a five-year warranty, in homes more than two years old where an existing system is replaced.
For a wall split, The Quote Yard's Melbourne servicing table gives $140 to $230 for a single split, and QuickAir gives $120 to $220 for a standard service with no faults. A deep clean is priced separately: Mr Duct charges $180 for the first indoor unit, $160 for the second, $150 for the third and $140 for each after that, including the outdoor unit and GST, and QuickAir lists a chemical-wash deep clean at $200 to $350. For a gas ducted heater, Climate Control Solutions gives $180 to $320 for a service with no faults, and homeupkeep gives $280 to $380 for a service with a carbon monoxide test. Duct cleaning is a separate service: The Quote Yard puts it at $250 to $600, and Mr Duct starts at $260 for five outlets plus $10 for each extra outlet.
A rooftop evaporative cooler serviced before summer, with the pads checked, runs $170 to $330 in The Quote Yard's Melbourne table, an inspection that does not include new pads; no reliable pad price is quoted here because the source contradicts itself, and no source gives an evaporative repair call-out. For repairs, The Quote Yard says most actual repairs land between $300 and $900, and its fitted prices include $180 to $400 for a capacitor and $400 to $900 for a leak repair and recharge. Whatsthedamage gives $315 to $1,250 for a major repair or regas. On the gas heater side, homeupkeep lists an ignition repair at $180 to $320 and a flue repair at $380 to $680. The Quote Yard adds that after-hours attendance carries a premium of fifty to one hundred per cent.

Air Conditioning Installation
Air conditioning installation in Brighton VIC: split, multi-head or ducted systems sized by heat load, sited for bayside salt air and quoted in writing after an inspection.

Split System Installation
Split system installation in Brighton VIC: high-wall, floor-standing and multi-head splits installed to the manufacturer's manual and quoted in writing after an inspection.

Ducted Air Conditioning
Ducted air conditioning in Brighton VIC: reverse cycle, add-on cooling and new-build systems, zoned room by room and quoted in writing after a roof space inspection.

Reverse Cycle Air Conditioning
Reverse cycle air conditioning in Brighton VIC: heat pump heating and summer cooling from one system, fitted as splits, ducted or a hybrid unit, quoted in writing.

Evaporative Cooler Service and Repairs
Evaporative cooler service in Brighton VIC: pads, tray, bleed, pump and fan checked before summer, repairs for warm air and noisy fans, and a written record.

Air Conditioning Repair
Air conditioning repair in Brighton VIC: split, multi-head and ducted faults diagnosed, leaks found before any regas, salt-corroded coils checked, and a written quote first.

Emergency Air Conditioning Repair
Urgent air conditioning breakdowns in Brighton VIC, booked 6am to 10pm seven days: ceiling leaks, electrical faults and heatwave failures, with rates stated in the call.

Air Conditioning Service
Air conditioning service in Brighton VIC for split, multi-head and ducted systems: filters, coils, drains, outdoor units and electrical checks, with readings recorded.

Aircon Cleaning
Aircon cleaning in Brighton VIC: split system coils, barrel fans and drain trays cleaned inside the unit, with a wash bag fitted and every unit quoted in writing.

Ducted Heating
Ducted heating in Brighton VIC: new and replacement gas ducted heaters or electric ducted systems, with heater position, gas supply, flue and ducts checked before a written quote.

Ducted Heating Service and Repairs
Gas ducted heater servicing in Brighton VIC: two-yearly services to the maker's schedule, CO spillage testing, rental gas safety checks, duct cleaning and error code repairs.

Commercial Air Conditioning
Commercial air conditioning in Brighton VIC: splits, cassettes, rooftop packaged units and VRF for shops, offices and industrial units, with servicing and leak checks.
air conditioning In Hampton East
Whatsthedamage's Melbourne table (updated November 2026) puts a supplied and installed split at $1,250 to $2,625 for 2.5 kW and $1,475 to $2,950 for 3.5 kW. Ducted reverse cycle runs from $8,400 to $14,700 in its standard band, rising to $12,600 to $23,100 for larger, two-storey or room-by-room zoned homes. These are a cost guide's indicative ranges, not a quoted price. The final figure follows an inspection and a written quote.
The Quote Yard's Victorian repairs guide gives a rule of thumb: "Where the repair exceeds roughly half the cost of a new system, and the existing unit is past about ten years, replacement is usually the better decision. Below either of those thresholds, repairing is generally sensible." Its fitted prices show where that line can fall: a compressor at $1,400 to $2,800, against $1,475 to $2,950 for a supplied and installed 3.5 kW split in Melbourne on whatsthedamage.com.au. The system's age is on the data plate of the outdoor unit, so check it before comparing a written repair quote with a replacement quote.
ActronAir is one brand that builds some of its range here. Its Australian-made page says a number of its residential split ducted systems, its commercial packaged and split ducted systems and a range of controls are designed and built in Australia, with manufacturing at its Marsden Park headquarters, and it notes that not all of its products are Australian Made. Where a unit is made is a separate question from how it performs, so whatever the brand, compare models on the Energy Rating label, the warranty and how readily parts are available.
Yes, after the sheeting is checked. The Better Health Channel says houses built before the mid-1980s are highly likely to contain asbestos products, including fibro cladding and eave linings, and that drilling can release fibres. The only way to be certain is to have a sample tested by an accredited laboratory, and untested material should be treated as if it contains asbestos. So the pipe hole is either drilled after a clear test or moved to a wall that is not fibro. Any removal is work for a licensed asbestos removalist, not an air conditioning installer.
It is often worth doing first. Sustainability Victoria's archived guide says double-fronted brick veneer houses are likely to have only a small amount of ceiling insulation, and that topping it up will improve winter comfort and reduce energy use. YourHome says roof and ceiling insulation can save 45 percent or more on heating and cooling costs. A better insulated house can need a smaller heat pump, so the size is best chosen after the ceiling is checked. If the work is planned for later, the quote should say which state of the house the unit is sized for.
Usually not. Clause 62.02-2 of the Bayside Planning Scheme exempts domestic services such as an air conditioner unless a permit is specifically required. A Heritage Overlay is the main exception: on a listed house, a unit visible from a street, other than a lane, or a public park needs a permit, and the schedule names five Hampton East places. Search the Schedule to the Heritage Overlay or look the address up on VicPlan, then check with Bayside City Council. Apartments also need the owners corporation's approval.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm