Ducted heating service Brighton VIC 3186 covers the gas ducted heater itself, the ducts that carry its warm air and the safety checks that Victorian rules and the manufacturers set for it. Peak Air Conditioning Brighton books two-yearly heater services worked through the maker's maintenance schedule, carbon monoxide spillage testing under AS 4575, rental gas safety checks, duct and return air cleaning, and repair visits for error codes, lockouts and noisy fans. Gas work on the heater is done by a licensed gasfitter registered with the Building and Plumbing Commission and endorsed for Type A appliance servicing. The Commission requires that gasfitter to give the customer a copy of the complete gas servicing record within 5 days of the work. Bookings are taken from 6am to 10pm, seven days a week.
GET A FREE QUOTE
Two things shape how a heating or cooling job in Brighton starts: knowing what each option costs before anything is booked, and finding a visit time that suits the household. Peak Air Conditioning Brighton is set up around both. Prices are put in writing after the site visit, option by option, and the phone line takes bookings for new systems, servicing, aircon cleaning and repairs from 6am to 10pm, seven days a week.
Peak Air Conditioning Brighton
Three different bookings sit under the name ducted heating service, and each has its own trigger and its own rule book. The heater service follows the manufacturer's interval and the heater's own service reminder. A rental gas safety check follows a legal two-year cycle set out by Consumer Affairs Victoria. Duct cleaning follows a separate, longer interval in the Brivis manual. The parts below set out when each one is due; what the gasfitter actually checks on the heater is set out in the next section.
Two of the three manufacturer documents read for this page set a two-year interval. Brivis's Ducted Gas Heater Operation Manual (Issue D, covering the StarPro SP6, SP5 and SP4, Buffalo BX5C and BX3C, Wombat 2PWN and Compact CC3) says the heater should be serviced at 2 year intervals by authorised personnel trained to service these models, and its maintenance table runs from year 2 to year 12 in two-year steps. Braemar's ducted gas heater owner's manual asks for its schedule items to be checked every two years after the date of installation, and asks owners to keep to that two-year cycle after the warranty period ends. Braemar's TG3 Series home owners guide is the exception: it says maintenance should be performed on a yearly basis, so a TG3 owner follows the shorter figure printed for that model. Energy Safe Victoria's advice for every gas heater matches the two-year figure: its heating page recommends that all gas heaters are serviced at least every two years by a qualified gasfitter, and lists central heating units among the heaters that can spill carbon monoxide.
The heater can also ask for its own service. On Brivis heaters with a Networker wall controller, when the logged operating hours reach a set duration the spanner symbol flashes once per second and a message reads "Fan run hours indicate it is time for a service call". A spanner shown with a scrolling error message is a different thing: it marks a fault or lockout, which the repairs section at the end of this page covers. The manual asks the owner to write down the date and the message, since those are what a technician will ask for.
A rented home has a legal cycle on top of the manufacturer's. Consumer Affairs Victoria's page for rental providers on gas and electrical safety, last updated 14 October 2026 and read on 20 November 2026, says: "Rental providers must have a gas safety check done every 2 years by a licensed or registered gasfitter." It adds that the check must be conducted by a gasfitter "who is endorsed in the specialised class of Type A Gas Appliances Servicing - Gas Servicing Type A on the Plumbers Identity Card". The check is wider than a heater service. Among other items, the page lists testing gas installations for leakage, checking the condition of appliance flue systems, adequate ventilation, access to appliances for servicing and, for a standard gas installation, servicing all Type A gas appliances that are part of it, which takes in a gas ducted heater. It also requires testing to confirm that those appliances are serviced in compliance with AS 4575.
The paperwork runs both ways. Before a rental agreement is entered into, the rental provider must disclose the date of the last gas safety check and any outstanding recommendations from it, and "a copy of the most recent gas safety check must be provided to the renter within 7 days after the rental provider receives a written request from the renter." The ABS 2021 Census counts 23.7% of Brighton's occupied dwellings as rented, against 28.5% for Victoria, which is the share of local homes where this two-year rule can apply alongside the manufacturer's own interval.
Duct cleaning has its own interval, and it is longer than the heater's. Brivis's operation manual says "It is recommended that ducting is cleaned every 3 years", and its FAQ lists what the job involves: removing dust, odours and pet hair from the heating system, checking whether a return air filter is fitted and cleaning it if so, cleaning the return air grille and duct, cleaning the heater fan and assembly, and cleaning the supply air registers and their boots. Mr Duct Cleaning, a Melbourne duct cleaner, describes the same scope from the cleaner's side, covering the supply and return air ducts, registers and grilles, and says professional cleaners use high-powered vacuums and air-pressure tools to dislodge the debris and draw it out without spreading it back into the house. Cleaning the coil and barrel fan of a wall split system is a different job again, covered under aircon cleaning.
Between cleans the owner has two jobs. Brivis and Braemar both say the return air filter, where one is fitted, must be cleaned at least every two weeks during the heating season; it usually sits in the return air grille on a wall or ceiling, and a vacuum cleaner does the job. Better Health, the Victorian Department of Health's site, adds that duct registers and cold air return vents can be vacuumed out with the heater off and cool. Both maintenance schedules also list duct condition, so a heater service is a chance to look at the ducts even in a year when they are not due for cleaning. Duct cleaning prices are set out in the cost section below.
Peak Air Conditioning Brighton
Brivis's operation manual sums a heater service up as maintenance and adjustment of four components: the burners, the ignition system, the fan assembly and the heat exchanger. Its FAQ adds a check of the gas supply flow and lock-up pressure. The five parts below follow those items through Brivis's StarPro SP5 and SP6 service manual, which also covers SP4 and BX5 models, and the Brivis Classic installer's manual. Each figure is stated as that manual's own, and other makes publish their own procedures. A gas ducted heater is a Type A gas appliance, so every step here is gas work for a licensed gasfitter; Energy Safe Victoria's advice is not to attempt to fix a gas heater yourself.
The StarPro service manual describes in-shot burners: each one draws primary air in near its injector through a venturi to mix with the gas, and a cross lighting gallery near the burner exit carries the flame from one burner to the next. Brivis's FAQ puts "Clean burners" first on its list of what is done in a service, and Brivis's schedule and Braemar's both give burners and injectors a line of their own. Braemar's schedule also lists cross-lighting as an operation check, a check that the flame carries from burner to burner once they are clean.
Ignition comes next. The manual describes a spark igniter made of a spark probe and an earth probe that form a fixed gap, much like a spark plug, beneath the burner port at one end of the burner rack. Its servicing step is to check the electrode, lead and plug, clean the igniter probe and confirm a spark gap of approximately 4 mm. At the opposite end of the rack, the flame sensor proves the flame by passing a small current through it, and if that current is too low the control shuts the gas valve. The manual's check is that the flame sensor rod is clean, located correctly, and that its lead and plug connection is in good condition. Both steps start with the heater's power and gas supply isolated. Brivis lists the igniter and the flame sensor among the consumables that may need periodic replacement, so their condition is checked at each service.
The heat exchanger and flue carry the combustion gases, so this is the part of the service most closely tied to carbon monoxide. Brivis's service manual explains that the combustion fan pulls air through the heat exchanger to draw the flame in and feed it, and that if this airflow is reduced, "the combustion quality will be reduced and sooting may occur." Soot is therefore the sign the gasfitter looks for. One of the manual's checklists asks whether "the flue terminal or flue pipe has soot marks, indicating poor combustion and/or a possible blocked heat exchanger," and its combustion fan check looks for a build-up of soot or silicon in the fan housing or flue pipe, to be cleaned if necessary.
Brivis's FAQ lists "Check/clean the heat exchanger" among the service tasks, and its maintenance schedule records the heat exchanger, the flue system and the flue termination or cowl as separate lines; Braemar's schedule has its own heat exchanger and flue system lines. Energy Safe Victoria names a flue that is partially or totally blocked as one of the conditions under which high carbon monoxide levels can occur, and Better Health recommends professional servicing that includes inspection of the flue or chimney. The service records what was found and cleans what can be cleaned. Whether a damaged heat exchanger is worth repairing, or is the point at which replacing the heater makes more sense, is a separate decision weighed after the service, with the heater's age and star rating in view.
A heater that lights and runs can still be burning the wrong amount of gas, and only a pressure reading shows it. Brivis's service manual sets out the check on the gas valve's two test points. For the inlet reading, the gasfitter loosens the inlet test point screw, connects a manometer, runs the heater until the flame proving period ends, reads the pressure, then removes the manometer and retightens the screw straight away to prevent a gas leak. For the burner reading, a manometer goes on the burner pressure test point while the controls force the gas valve to its maximum rate and then its minimum, and each is adjusted at its own screw on the valve if it sits outside specification, high rate first. The manual's conclusion is blunt: "If the gas valve cannot be set to the specified maximum and minimum burner pressures, then the gas valve will have to be replaced."
The figures themselves are model-specific. The Classic installer's manual asks for the burner pressure to equal the figure shown on the appliance data label, and Braemar's schedule has kPa boxes for the gas inlet pressure and for the high and low test point pressures, so the readings are written down rather than simply checked. For that reason no pressure figure is quoted on this page. Low inlet pressure matters beyond the gauge: the StarPro manual says it can cause unreliable ignition and underrated heat output, so the reading can explain a heater that struggles to light or never quite warms the house. Brivis's FAQ also lists a check of the gas supply's lock-up pressure alongside the flowing reading.
A gas ducted heater has two fans with two different jobs. The main fan, a centrifugal fan in a metal scroll on the StarPro range, pushes warmed air through the ducts; the combustion fan pulls air through the burners and heat exchanger and out of the flue. Brivis's service manual gives each its own routine. For the main fan, the heater is switched off and isolated, the fan assembly is removed, and the gasfitter checks for any signs of wear, then rotates the fan wheel and listens "for any irregular noise such as scraping or worn bearings." The impellor, motor, housing and the fan compartment's inner lining are cleaned, and the wiring and plugs, including the speed sensor, are checked on reassembly. On internal models the manual has the heater split to reach the fan, so on a roof or underfloor heater this step involves more work than on an external one.
For the combustion fan, the checks are that the motor shaft spins freely and that there is no bearing or scraping noise while the fan runs its pre-purge at start-up, which the manual puts at approximately 15 seconds. It notes that a "tinkling" sound, made by the impellor clearing water particles out of the fan housing, is normal. Brivis's schedule lists the supply air fan motor, its capacitor and the combustion fan motor as separate lines, with the fan capacitor also listed as a consumable, and Braemar's schedule lists the room fan motor and impellor and the combustion fan suction pressure, which is the reading that shows whether the combustion fan is pulling as it should.
The last check on the service is a temperature one, and both manufacturers write it into their schedules. Brivis's maintenance table has boxes for the return air temperature and for the outlet air temperature at the closest register to the heater, and Braemar's has return air, outlet air and thermistor temperatures. The gap between the two readings shows whether the heater is moving enough air for the heat it makes. The Brivis Classic installer's manual sets a limit for that gap, saying the warm air at any outlet is not more than 45 °C above the return air temperature. The StarPro service manual marks the fault end of the scale for its own models: a rise of 47 °C over the return air temperature indicates a true overheat condition.
A dirty return air filter is one of the overheat causes the manuals name, so it is checked at the same time. Braemar's owner's manual says the filter must be checked and cleaned by the owner at least once every 2 weeks during the heating season, that regular cleaning keeps the heater running efficiently, and that the owner pays for any service call caused by failing to clean it. Brivis's manual says a blocked filter significantly affects heater performance and efficiency, and warns never to run the system without the return air filter in place where add-on air conditioning is installed. Ducts shared with a cooling coil are covered under ducted air conditioning, while the heating side of the reading belongs to this service.
Peak Air Conditioning Brighton
The two parts below cover what an owner can check for themselves: the gasfitter's licence before the work, and the schedule and record after it. Peak Air Conditioning Brighton gives the service price when the booking is made, quotes any repair before it goes ahead, and has the gas work on the heater done by a licensed gasfitter registered with the Building and Plumbing Commission. The phone line is answered between 6 in the morning and 10 at night on every day of the week, which leaves room to book a visit around work hours or a tenant's access.
Not every gasfitter may service a gas ducted heater. The Building and Plumbing Commission's AS 4575 page, last updated 28 August 2026, says: "Only plumbers who are registered or licensed in the specialised class of Type A appliance servicing can carry out Type A appliance gas servicing work." It adds that a registered person in that class must work under the supervision of a person who holds a licence to service Type A gas appliances. Energy Safe Victoria's classification lists central heaters among Type A appliances, and its heating advice says that when looking to service and repair your gas heater, you should be sure it is done by a licensed Type A gasfitter.
The check takes a minute. Better Health says a registered and licensed gasfitter has a photo ID card "that states what kinds of work they are allowed to do", which they should carry and which you can ask to see at any time, and that the Type A endorsement can also be checked on the Commission's website. Energy Safe Victoria suggests asking, when the gasfitter attends, to check the licence card and the registered classes listed on the back of it. Consumer Affairs Victoria names the exact wording to look for on a rental check: Gas Servicing Type A on the Plumbers Identity Card. The card belongs to the person rather than the business, so the card worth checking is the one carried by the gasfitter who does the work on the day.
A service worked through the manufacturer's schedule leaves a record, and the record is the point. Brivis's operation manual prints its Service Maintenance Schedule as a table with a column for each two-yearly visit from year 2 to year 12, a line for the service date and the service company or technician, and rows grouped under electrical, heating assembly, major components, controls, system operation, installation-related items and consumables. Readings go in as numbers, in kPa, °C and, on the CO level line, PPM. Every other row gets an action code: inspected and working correctly, adjusted, cleaned, replaced, repaired, or referred to installer. Braemar's owner's manual has its own version, with columns for years 2 to 10, the technician's printed name and company, a signature, the date of attendance and a key for inspected, adjusted, cleaned and replaced.
The law adds a second record. The Building and Plumbing Commission says the gasfitter must give the customer a copy of the complete gas servicing record, including the completed AS 4575 Appendix E checklist, within 5 days of the work, and must keep a copy themselves for 10 years; the record lists the appliance's make, model, model number, gas type and serial number. Both manuals also tie the completed schedule to the product warranty, so an owner whose heater is still under warranty should read its terms on who may carry out the service. Other makes print their own schedules, and the one worked through is the schedule in the manual for the heater on site.
Peak Air Conditioning Brighton
The figures below are indicative ranges from Melbourne cost guides and a Melbourne duct cleaner, each attributed to its source; none of them is this business's price. None of the guides gives a standard-hours call-out for a gas ducted heater repair, so the call-out is confirmed when the visit is booked. What a particular service costs depends on the heater's make and position, the access to it, and what the schedule turns up.
Two Melbourne guides price a standard service where no faults are found. Climate Control Solutions, a Melbourne installer writing in August 2026, puts a gas ducted heating service at $180 to $320. Homeupkeep's Melbourne gas ducted page, last updated 14 June 2026, puts a standard service at $220 to $320, and lists a service plus a carbon monoxide test as a separate line at $280 to $380. The same guide prices an annual service contract at $180 to $280 a year. That is the guide's product rather than a manufacturer interval: the Brivis and Braemar owner's manuals read for this page ask for a service every two years, and Braemar's TG3 guide every year.
The split between a service with and without a CO test needs care in Victoria. The Building and Plumbing Commission says gas servicing work in Victoria must be carried out in accordance with AS 4575, and that its Appendix E checklist includes carbon monoxide testing. On that basis a Victorian service to AS 4575 is expected to include a CO test, and a quote priced at the lower line is worth one question: does it include the Appendix E checklist and the CO reading? The figure for a particular heater also moves with where it sits. Homeupkeep's guide observes that external cabinet units are the cheapest to service, and Brivis's operation manual notes that some installations require two service personnel to attend under health and safety requirements, with an extra charge possible on its own service calls when that applies.
When a service or a fault call finds a failed part, homeupkeep's Melbourne guide gives parts-and-labour ranges for the common ones: an ignition repair at $180 to $320, a gas valve at $280 to $450, a fan motor at $320 to $580, a wired thermostat at $180 to $320 and a flue at $380 to $680. These are the guide's own estimates, not quotes. The manuals explain why some of them come up. Brivis lists the igniter, the flame sensor and the fan capacitor as consumables that may need periodic replacement, and its service manual says a gas valve that cannot be set to its specified burner pressures has to be replaced. The heat exchanger sits in a different bracket: homeupkeep prices it at $1,200 to $2,800, a figure better read against the price of a new heater than as a routine repair.
The call-out is where the guides are thinnest. None of the sources researched for this site gives a standard-hours call-out for a gas ducted heater repair. The Quote Yard's Victorian gas fitting guide, published 28 February 2026, says most Victorian gas fitters charge a call-out fee of $80 to $130 and an hourly rate of $90 to $140, but that is a typical Victorian gas fitter call-out for gas fitting in general, not a heater repair price. Homeupkeep puts an emergency call-out for gas ducted heating at $250 to $450. The call-out for a Brighton visit is confirmed when it is booked, and the parts and labour are quoted after the diagnosis.
Duct cleaning is priced by the outlet. Mr Duct Cleaning's Melbourne guide, dated 29 May 2026, says its pricing for a single-storey home starts at $260 for 5 outlets, with each additional outlet adding $10, and that most Melbourne homes have 6 to 10 outlets, which puts its total at $270 to $310. It says that price covers the ducts, a return air filter clean and a clean of the internal unit, fan and motor. The same guide puts the Australian range for a standard home at $200 to $700, and a flat rate for the whole job at typically $300 to $500, depending on the number of vents, access to the ductwork and extras such as sanitising or deodorising. The Quote Yard's Victorian servicing guide lists duct cleaning at $250 to $600 as a separate service, and Climate Control Solutions prices a heater service with a deep clean of the return air and ductwork at $280 to $450.
Several of those drivers apply directly to a larger home. Mr Duct's guide says a single-storey three-bedroom home might have 10 to 12 ducts while a two-storey home with zoning could have 15 or more, and that ducts in tight crawl spaces or ceiling cavities take longer. Its $260 starting price is for a single-storey home, so a two-storey home is quoted on its own layout. The ABS 2021 Census counts 33.1% of Brighton's occupied dwellings with 4 or more bedrooms, so the outlet count is worth confirming before any figure is compared. Replacing ducts is a different job from cleaning them and is not priced here.
Peak Air Conditioning Brighton
A service and a repair are booked differently, because one starts from a schedule and the other starts from a fault. The three parts below cover how each is booked and what happens when a service turns up something that needs fixing. The faults themselves, and the codes that point to them, are covered in the repairs section at the end of this page, and the prices in the cost section above.
A service is a planned visit with a scope set before anyone arrives: the items in the manufacturer's schedule, the readings it asks for and the AS 4575 checklist the gasfitter completes. Because the scope is fixed, the service can be priced when it is booked, and its date can be chosen rather than forced. Brivis's operation manual gives a practical reason to choose a date before the cold arrives. It recommends shutting a heater down for summer by turning off the external gas cock and switching off its power, and it notes that several attempts may be needed to start a heater that has been shut down for an extended period, because air has to be purged from the gas pipe. On that guidance, a service before winter means the restart, the purge and the checks happen on a planned day rather than on the first cold night.
Booking ahead also helps with access. Brivis says every heater must have safe and reasonable access and be installed in compliance with its instructions, and Braemar's manual asks owners of an outdoor heater to check once a year that vegetation has not grown into or around the unit. Clearing a path to a roof access hatch, an underfloor opening or a side passage before the visit keeps the service to its planned scope. In a rented home, Consumer Affairs Victoria's gas safety check already includes servicing the Type A appliances in a standard gas installation, so the two-yearly check and the heater service can be planned as one visit.
A repair visit starts with a heater that has stopped or is misbehaving, so its scope is unknown until the fault is found. Brivis's operation manual sets out the owner's part. Before calling, run through its basic checks and troubleshooting table, then note what the controller shows: the manual asks for the date and the message to be written down, and says that if a technician is needed, the message, the model and the type of appliance should be given. Braemar's manuals make the same request in their own words, asking owners to run through the troubleshooting checks first and to have the model and serial number ready, which the TG3 guide says are located on the side of the heater.
That information shapes the visit. The gasfitter starts with diagnosis, working from the controller's message and the manufacturer's service checklists, and only then can say which part has failed. The part, its labour and any return trip are quoted at that point, before the repair goes ahead, because the service manual's checklists show that one message can lead to several different parts. A repair visit is aimed at the fault rather than the whole schedule, so it fixes the fault and confirms the heater is safe to run. Where the heater is past its manufacturer's service interval, the repair is a sensible time to book the full service too, so the schedule restarts from a known date.
A service sometimes finds something that needs more than cleaning or adjustment, and there are two ways it can go. Where the part is carried on the day and the owner approves the price, it can be repaired on the same visit. Where the part has to be ordered, or the owner wants time to decide, the repair is booked back for another visit, with the written quote in hand in the meantime. Either way the fault is quoted before the work starts, and the service record notes what was found.
One kind of fault does not wait for a decision. The Building and Plumbing Commission says that if a gasfitter identifies a safety-critical non-compliance, giving gas leaks, spillage of combustion products and overheating or scorching of surfaces as examples, they must notify the owner and make the installation safe straight away, which may involve repairing, isolating or disconnecting the appliance. If the customer does not consent to fixing or isolating it, the gasfitter must notify Energy Safe Victoria. So a heater can be left switched off and isolated after a service until a repair is approved. The schedules allow for each outcome: Brivis's action codes include repaired and referred to installer, so the record shows whether a fault was fixed on the day, left for a return visit, or handed back to whoever installed the system.
Peak Air Conditioning Brighton
Energy Safe Victoria's heating advice starts with the risk: "Carbon monoxide (CO) is a gas you can't see or smell," and "Any gas heater can spill CO", central heating units included. This page makes no health claims of its own. The four parts below cover the test that measures spillage, the warning signs the government sources list, the flue terminal outside, and the alarm that backs the service up.
In Victoria the carbon monoxide test is part of the servicing standard, not an extra. The Building and Plumbing Commission says gas servicing work must be carried out in accordance with AS 4575, the standard for servicing Type A gas appliances, that the amendments mandating it came into effect on 1 June 2022, and that gasfitters must comply with all of it, "including the Appendix E checklist, which includes carbon monoxide testing." It describes Type A servicing as the internal cleaning, maintenance and adjustment of the appliance, and the adjustment, repair or replacement of a component. Energy Safe Victoria describes the same visit from the owner's side: "A qualified gasfitter will inspect your heater and check its installation, including testing for CO leakage."
AS 4575 is sold by Standards Australia, so this page quotes no clause from it and gives no CO limit. The manufacturer's schedule shows where the result goes: Brivis's table has a CO level line, read in PPM, at each two-yearly service. A spillage finding is one of the safety-critical results described in the booking section above, which the gasfitter must make safe on the spot. Energy Safe Victoria's list of the conditions that can raise CO levels explains what the test is looking for: an appliance that is faulty or not maintained, a flue that is partially or totally blocked, and an appliance installed without adequate ventilation.
Better Health's gas heating page lists the signs that a gas heater needs a service: it has not been serviced for 2 years; there is a yellow or sooty flame, unless it is a decorative gas log fire; the pilot light goes out unexpectedly, or pops or bangs when lighting; there are signs of heat damage such as discolouration of the walls or heater panels; the walls become too hot to touch while the heater is on; there are soot stains around the heater; or there is any sign of trouble. Energy Safe Victoria's own wording is narrower. It says to check for changes in how your gas heater operates, "for example if the flame changes from its usual colour," and that after any change a qualified gasfitter must inspect the heater and check it for CO leakage.
Those lists cover every kind of gas heater, and a ducted heater shows the signs in its own places. Its burners sit inside a closed cabinet in the roof, under the floor or outside, and Brivis's FAQ says these heaters use direct spark electronic ignition with no pilot light, so the flame and pilot signs are rarely visible to the owner. What can be seen is soot at the flue terminal, the sign Brivis's service manual links to poor combustion, and heat discolouration on the heater's panels. The Building and Plumbing Commission lists overheating or scorching of surfaces among the safety-critical faults, the same family of sign as a wall too hot to touch. One sign has an innocent cause: Brivis says fumes from candles, oil burners, cooking or smoking can be drawn in through the return air and stain around the outlets. For anything else, Brivis's rule is plain: if there is excessive noise, smell or smoke, turn the appliance off, isolate the power supply and contact a service agent.
The flue terminal is the one part of a ducted heater's combustion path that the owner sees every day, and Brivis's operation manual gives the owner three rules for it. Do not hose the flue terminal. Ensure the flue terminals are kept clear of plant growth or any other obstructions. And, in its checks before calling for assistance, make sure the flue terminal is in place whenever the unit runs, that it is clear of leaves and obstructions, and that the air intake at the burner end of the heater's roof panel is clear as well. The manual warns that the flue outlet can become very hot, so none of this is done while the heater is running.
Energy Safe Victoria explains why it matters: high carbon monoxide levels can occur when a flue is partially or totally blocked. Its advice written for open-flued heaters makes the same point about the outdoor end of the flue, saying to keep plants and animal nests away from it because a blockage can push CO back into the house. Braemar's manual asks owners of an outdoor heater to make a yearly visual check that plants, branches and weeds have not grown into or around the unit and that leaves and other debris have not built up on the cabinet, and it says not to enclose an outdoor heater. Some things at the flue are normal: Brivis says vapour discharging from the flue terminal while the heater runs is not unusual. The distances a flue must keep from windows, doors and meters belong to the install rather than the service, so they are not repeated here.
A carbon monoxide alarm is a back-up, and both government sources say so in nearly the same words. Better Health says CO alarms "can be a useful back-up precaution, but should not be considered a substitute for the proper installation and maintenance of gas heating appliances," and Energy Safe Victoria says an alarm "will help but should never be a substitute for regular servicing." There is no Australian standard to buy against. Better Health says no standard in Australia covers the design, manufacture, installation or servicing of CO alarms for domestic premises, so an alarm should be certified to the European EN50291 or the US UL2034 standard, and Energy Safe Victoria says the alarm itself will indicate which of the two it complies with.
Both sources add practical points. Choose an alarm with visual and audible warnings that show when the electrochemical sensor or the battery has expired. Better Health notes that alarm manufacturers suggest installing one in or near every room that has a gas heating appliance, audible from all sleeping areas. Energy Safe Victoria cautions that an alarm's effectiveness is limited to the location where it is installed, as CO levels elsewhere in the room may vary, says to follow the manufacturer's installation instructions on where it goes, and says hard-wired alarms must be installed by a licensed electrician. None of this changes the service interval: the alarm sits beside the two-yearly service, not in place of it.
Peak Air Conditioning Brighton
The codes below are Brivis codes, from the Ducted Gas Heater Operation Manual, Issue D (StarPro SP6, SP5 and SP4, Buffalo BX5C and BX3C, Wombat 2PWN and Compact CC3) and Rinnai's matching error code sheet, with the technician's checks from the StarPro SP5 and SP6 service manual. Other makes use their own codes, so a Braemar or any other heater is diagnosed from its own manual. Brivis lists owner checks only for the codes it says customers may safely work through; everything inside the cabinet is gas work for a licensed gasfitter. Faults in a refrigerated cooling system that shares the ducts are covered under air conditioning repair.
Codes 40, 41, 42 and 43 mean an overheat condition has occurred, and the operation manual says the fan will operate at maximum speed. The StarPro service manual explains what happens inside: overheat switches interrupt the 24 volt power to the gas valve, so the burners stop while the fan keeps running to carry the heat away, and once the switch resets the heater can resume if the controller is still calling for heat. Code 53 is the lockout when it keeps happening. The operation manual calls it a lockout due to multiple overheat occurrences, with the primary cause "typically associated with insufficient airflow", and the service manual defines it as 2 consecutive over temperature conditions within 15 minutes.
The owner's checks for all of these are the same three: enough outlets open on the duct system, the floor or ceiling register and its baffle fully open, and the return air filter sized correctly, clean and unobstructed, with nothing placed in front of the return air grille. For 53, reset the heater, and if the error persists, contact the installer. The gasfitter's list goes further: comparing the nearest-outlet temperature with the supply air thermistor, checking the fan speed is sufficient for the system and the fan motor is working and unobstructed, and checking that the ducting has not been crushed, damaged or incorrectly sized. The service manual also lists a ceiling-mounted heater with a high level return air grille as a case to check. A fan that runs on briefly after the heater is turned off is normal: Braemar's manual says its room fan stops approximately 60 to 90 seconds after switch-off.
Codes 46, 47 and 55 mean the heater has failed to ignite within the specified time, and Rinnai's error code sheet marks them as a service call. Code 50 is the lockout that follows repeated failed attempts. Brivis's documents count those attempts differently: the operation manual and the error code sheet say four, while the StarPro SP5 and SP6 service manual and the Classic installer's manual say five, so the lockout matters more than the count. For code 50 the owner can reset the heater and check that gas is on at the meter and at the appliance gas cock, that other gas appliances such as the cooker and hot water service are working, and that gas is reaching the home, since there may be works in the area. The manual's last line for this code is "The heater may require a general service."
The service manual's checklist for a heater that does not light follows the ignition chain in order: whether there is a spark across the igniter gap; whether gas is on at the meter and the appliance cock; whether the inlet pressure is sufficient during ignition; whether the burner pressure during ignition is within specification; and whether air has been purged from the gas piping. Where the flame lights but is not proved, it checks that the flame sensor is connected, correctly positioned and clean. Only after all of those does it suggest the gas valve or the control board may be at fault, changing them one at a time to prove which. A heater restarted after a long summer shutdown may simply need several attempts while air is purged from the pipe, which the operation manual describes as expected for a new installation or one shut down for an extended period.
Code 56 is a lockout on the pressure switch, which the operation manual says is usually caused by too much restriction on the flue pipe, or the condensate drain on SP6 models. The service manual explains what the switch does. During the pre-purge at start-up the combustion fan draws air through the heat exchanger, and a vacuum pressure switch confirms there is enough airflow for safe combustion; if the vacuum is too low the switch does not close, an error is logged and no ignition occurs. SP6 models carry a second switch in the condensate tank, which cuts the gas valve if the condensate level rises to the point where combustion quality is unsatisfactory. The operation manual says an SP6 can produce approximately 2 to 3 litres of condensate per hour under continuous running, depending on the size of the heater.
The owner's checks are to look for blockages in the flue pipe and, on SP6 models, in the condensate piping, and the manual's basic checks add that a blocked SP6 condensate tube will seriously affect performance and may shut the heater down. Rinnai's error code sheet adds one cause that needs no repair: gusty wind can open the pressure switch by blowing air back down the flue. Beyond the owner's checks, the service manual's list for this code includes a flue that is too restrictive for its configuration, condensate collecting in a flue pipe that lacks a continual fall back to the heater of 20 mm rise per metre, pressure hoses that are perished, cracked or holding water, heat exchanger leakage, and a faulty combustion fan. A gurgling sound from an SP6's inlet ports points to a condensate tank that is not draining properly.
Brivis's troubleshooting table gives whistling a single remedy: clean the return air grille and filter. The Classic installer's manual shows why the return air path is where noise starts. It asks for a return air grille large enough to accept the system's full air capacity at low noise levels and minimum resistance, and for registers and diffusers large enough and of good design to minimise noise. As a general rule of how air moves, a clogged filter shrinks that opening, so the same volume of air is drawn through less space. The same table's entry for a fan that will not turn off carries checks worth knowing too: make sure Fan Only has not been selected, that enough vents are open, that the grille and filter are clean, and that the ducting has not been crushed or collapsed, with customer care contacted if damage is evident.
Scraping is a different sound with a different source. The StarPro service manual's main fan routine has the gasfitter rotate the fan wheel and check for any irregular noise such as scraping or worn bearings, and its combustion fan routine listens for bearing or scraping noise during the pre-purge, so a scrape that begins as the heater starts can point to either fan. Its checklist for error 30, a missing fan speed signal, also includes checking for a loose fan impellor on the motor shaft. Not every sound is a fault: the same manual says a tinkling sound from the combustion fan clearing water particles is normal. A fan motor that has to be replaced is priced in the cost section above, and the repair is quoted once the gasfitter has confirmed which fan is at fault.

After the first call, a technician visits to look at the rooms to be heated or cooled, the walls, roof space or subfloor where equipment could go, the switchboard and any gas supply. The Victorian Energy Upgrades buyer's guide advises having installers check what size suits the home, because a system that is too large can use more energy and cost more to run.

The written quote names the system and its heating and cooling capacity, the unit positions, the pipe or duct route, any electrical or gas work, any approvals needed and the price of each option. Where a VEU discount applies, an accredited provider applies it before work starts, because the energy.vic.gov.au page says retrospective discounts are typically not possible.

The units are fitted, and the refrigerant pipework is pressure tested and evacuated before the system is charged. A licensed electrician does the wiring and issues a Certificate of Electrical Safety, and any gas work is done by a licensed gasfitter. Handover covers the modes, filter cleaning and the documents to keep.
Every two years for most gas ducted heaters. Brivis's operation manual says its heaters should be serviced at 2 year intervals, Braemar's ducted gas heater owner's manual sets a two-yearly schedule, and Energy Safe Victoria recommends that all gas heaters are serviced at least every two years by a qualified gasfitter. Braemar's TG3 Series guide asks for yearly maintenance, so the manual for the heater on site decides. A rented home also needs a gas safety check every 2 years under Consumer Affairs Victoria's rules, and a flashing spanner symbol on a Brivis controller is the heater's own reminder that a service is due.
Melbourne cost guides put a standard gas ducted heater service with no faults found at about $180 to $320 (Climate Control Solutions) or $220 to $320 (homeupkeep). Homeupkeep lists a service with a carbon monoxide test at $280 to $380. These are indicative ranges, not quotes, and neither is Peak Air Conditioning Brighton's own price. The figure for a particular heater moves with its position and access, and with any parts the service finds are needed.
In Victoria it should. The Building and Plumbing Commission says gas servicing work must follow AS 4575 and that its Appendix E checklist includes carbon monoxide testing, and Energy Safe Victoria says a qualified gasfitter will check the installation, including testing for CO leakage. Brivis's maintenance schedule has a line for the CO level in PPM at each service. Some cost guides still price a CO test as a separate line, so ask whether a quote includes the Appendix E checklist.
First rule out normal behaviour: Brivis says the heater will not operate if the room is already warmer than the set temperature, and Braemar's manual says its room fan runs on for approximately 60 to 90 seconds after switch-off. If the heater stops on an ignition lockout, code 50 on a Brivis controller, check that gas is on at the meter and at the heater's gas cock. Codes 40 to 43 mean an overheat, usually from restricted airflow, and 53 is the lockout after repeated overheats, so open more outlets, open the registers and clean the return air filter. If a code keeps returning after a reset, book a repair visit by a licensed gasfitter; other makes use their own codes.
Brivis's operation manual recommends cleaning the ducting every 3 years. Between cleans, Brivis and Braemar both say the return air filter should be cleaned at least every two weeks in the heating season, and Better Health suggests vacuuming out the registers and return air vents with the heater off and cool. Duct cleaning is a separate job from the heater service, and its prices are set out in the cost section of this page.
A licensed or registered gasfitter endorsed for Type A appliance servicing. The Building and Plumbing Commission says only plumbers registered or licensed in that specialised class can carry out Type A appliance gas servicing work, and Energy Safe Victoria classes central heaters as Type A appliances. For a rental gas safety check, Consumer Affairs Victoria looks for Gas Servicing Type A on the Plumbers Identity Card. You can ask to see the card on the day or check the licence on the Commission's website.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm